Søg i resultater

Søg i resultater 1-20 af 1.000. Der er endnu flere resultater, omdefiner venligst din søgning.

I går, 14:19

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

So around this time the machine looked like this and was actually functional. This is a picture of one of the very first boots The issue in my eyes was that the cabling looked terrible, despite the darkened glass, my friend could maybe notice and can not take any chances in not doing the best job i can with the time and parts available. Also, the supplied fan there came with the case is terribly loud, needed to be swapped. If you notice, there is also a huge hole in the PSU shroud, because I had...

I går, 14:03

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Unpacking the extremely cheap water AIO, still a mystery how thy can make it for this price, but it honestly really does a good job and come with pretty amazing fans for the price included in the box. Looks like actually pretty good quality If I should give it a little critique, the very thin tubes are very stiff and really difficult to route, so the only place I could mount the rad, have some nice smooth bends and have the coolermaster logo facing the right way on the block itself, was to place...

I går, 13:53

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Unpacking motherboard, thats how you build a very cheap no nonsense board, only the essentials but a little of everything The matching RAM The graphics card Unpacking the case, a rather nice frame to build within And so did the mounting begin

I går, 11:16

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Let's continue the story about how this PC came to life. It all started with me bringing home a lot of parts on my bike, as I don't have a car and live near the place were everything was delivered to. In case you forgot, this build is a Ryzen build, and they have pretty packaging All the parts: To be continued....

I går, 10:56

Forfatter: AT0MAC

Killer Panda - Z370 X Code

Citeret fra "Uber" Må Tweak.dk dele dine billeder mv på vores Facebook gruppe Det må Tweak.dk gerne Jeg lover at billederne snart bliver meget mere prima kvalitet, men at stille tingene nydeligt op når man har fingrene i maskinrummet er bare ikke helt sagen Jeg håber jeg idag får styr på noget cable management og det skulle i den grad hjælpe på kvaliteten

I går, 10:24

Forfatter: AT0MAC

Killer Panda - Z370 X Code

I had not intended to work on this friday, but instead of going to bed I decided to work. And when I finished the time was 3am... So just woke up now (saturday at 10). Test fitted many of the wires and components, its way more difficult than it looks. The front looks the same But from the side a few things are changed There is less space in the case than I remembered, so will have to limit the amount of fans I originally wanted to use. Im little excited to see how my graphics card will turn out ...

torsdag, 19. april 2018, 23:50

Forfatter: AT0MAC

Killer Panda - Z370 X Code

I make small progress all the time and try my best not to screw up too much, im so close now to be done so better go easy. Did some little more cable routing, and put grommets on the holes I have made, to avoid either cutting fingers and cutting cables, the aluminum is rather sharp when drilled trough I have riveted the last bits and pieces in and put feet under again, plus I made a extra support foot in the middle of the case, else its sagging down due to weight of pump and hdds Actually the bo...

torsdag, 19. april 2018, 15:58

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Citeret fra "jesper101996" Har lige bygget i et Meshify. Desværre havde proshop kun version med mørkt vindue. Ellers var det solidt at bygge i Jeg syntes faktisk den sorte glasplade er ret lækker, og det syntes min ven også, det var ikke meningen builded her skulle være flashy, så dæmpet belysning og skinnende glas giver den noget klasse og gør den alligevel meget mere 2018'agtig

tirsdag, 17. april 2018, 23:09

Forfatter: AT0MAC

Killer Panda - Z370 X Code

As I said, been working on a friends PC the past few days and it's now online so you can see what I been tinkering with on the sideline. So no update on this one today, as it really takes a while writing up a new thread and make the pictures the best I can do. Stay tuned for more Panda Power!

tirsdag, 17. april 2018, 23:02

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

And if you are in doubt about the thermals, I tested it for more than 8 hours in different apps, plus I ran 6 hours Prime95 Small FFT, plus 18 hours or so of Memtest86+ It's a solid build. Max 71/73 degree in a 24 degree room on GPU/CPU. Even Windows is a solid special blend I fixed him up with, no nonsense, no build in apps, no 3D this or that, no OneDrive and a lot more, it always takes me ages to install windows but the result is much faster than MS normally sells, pretty close to a LTSB edit...

tirsdag, 17. april 2018, 23:00

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

My friend is no overclocker, but its such a shame to not boost it just a little, so I gave him a very conservative OC that should be able to live on without any hickups

tirsdag, 17. april 2018, 22:59

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Now with the ugly pictures out of the way, ready for a closeup of the finished result? Here you go!

tirsdag, 17. april 2018, 22:59

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Meshify C front, simple, good airflow and looks good My best attempt at cable managing this case Really difficult taking pictures with tempered glass on! Still covered in plastic until he brought it home

tirsdag, 17. april 2018, 22:58

Forfatter: AT0MAC

(Gaming PC) Meshify C 1500X *QuietBudgetNinja*

Undskyld det igen foregår på engelsk, men jeg orker desværre ikke sidde og oversætte det hele da det praktisk talt vil have samme mening. I det mindste bare kig billeder, de siger alligevel det hele I have taken a break away from my new extraordinary complex build and taken on the task of finding parts, assembling and installing my friends new gaming computer. It was his birthday last Sunday so this years big gift for himself was a new PC. Been using a gaming laptop the past few years with no cl...

tirsdag, 17. april 2018, 10:18

Forfatter: AT0MAC

Killer Panda - Z370 X Code

Sorry for the few days of total silence, I have been building a friends computer and will make a separate post about that, it turned out pretty sweet! Lets get going with my own project. Have now finalized mounting the pump: Mounted the radiator, fans and fan frames Mounted the res, and mounted both light and temp sensor in it, temp sensor is just about the right size to not interfere with flow The banged up res will not be seen, as that's below it and sits totally flush with the motherboard tra...

onsdag, 11. april 2018, 18:17

Forfatter: AT0MAC

Killer Panda - Z370 X Code

Citeret fra "Uber" FEDT projekt! Fedt at du kigger med tråden er blevet lidt uoveskuelig at følge med i hvis ikke man hoppede på for en måned eller 2 siden, men vi er snart ved at være der hvor det bliver rigtig sjovt, når delene endeligt skal samles.

onsdag, 11. april 2018, 18:15

Forfatter: AT0MAC

Killer Panda - Z370 X Code

Citeret fra "Senosk" Afhængig af hvor gammel din 1-krone er, så er den lavet af kobbernikkel eller aluminiumsbronze (evt. guldfarvet) Din 25-ører fra 1967 med Frederik IX' monogram er lavet af kobbernikkel. Hvad de to andre er lavet af, det ved jeg ikke, men vil tro at den med 40 STD er lavet af aluminiumsbronze (guldfarvet) og pfenning er lavet i stål og derefter dyppet i kobber. Det vil jeg i hvert fald gå ud fra med henblik på min research. Det havde jeg ikke forventet et svar på, nice work!...

onsdag, 11. april 2018, 08:06

Forfatter: AT0MAC

Killer Panda - Z370 X Code

It's morning, about 9 hours later since I started blitzing the rad and I have some little time to update you guys before I rush to work. The coin control test have done something over night They turned more shinny, but not the grey coin, it started dissolving - proof that it at least works (not sure what metals the coins are but it at least did something) Its freaking difficult to show in the rad, but I can see that the bottom of it is way smoother than before, also some of the threading looks n...

Nyeste Videoer og Trailers

Partner sider
Indsend nyhed
Har du fundet en fed nyhed så indsend den så alle andre på Tweak.dk kan få glæde af den.