tirsdag, 22. maj 2018, 21:44

Today I passed by Ikea and picked up 4 boxes of tiny little mirrors, I think there is 8 mirrors in each box and first of all it took forever getting trough that huge store, it's quite far from where I live and lastly, god damn they are heavy little things!
I'm totally exhausted from that trip....
But ir's part of the plan, so everything should still hold up ;)

I'm going to be super busy tomorrow, there is a lot to do before the reveal:

* Make a hole in a shelf for my closet cooling solution.
* Mount set shelf im closet including 3x ML140 Pro LED fans
* Install fancy mirrors in closet
* Paint the air tunnel so moisture will not be a problem.
* Maybe install a fan inside each airtunnel, to help the ML140 at the beginning of it?
* Install dust filters in airtunnel
* Setup the new monitor
* Re-mount the old monitor in a new spot
* Take awesome pictures of the whole shebang !
* Reveal on thursday!!

There have been some minor changes to the system the past few days, like it will not have a magnet mounted quick release for the front/top cover, it was too difficult to make it work with the USB and power button also mounted on the front, and the fact that my clever little m.2 cooling solution makes the perforated side panel rattle due to turbulence, well that just means it will be with open side panels.

So I think I will mainly focus my time on the actual build reveal for thursday, and then the rest maybe later on thursday or in the coming days after, but I will try to get as much done as possible tomorrow.

For now I just need to relax, have unwrapped the new monitor and really enjoy it even that is is just temporary set up in this spot for now, it's HUUUGE!

See you sson with more finished work ;)

Min gaming PC: Killer Panda - Z370 X Code



torsdag, 24. maj 2018, 12:06


Just kidding, but bare with me - im post processing the pics I just took, just a few more minutes and you will see ;)

Min gaming PC: Killer Panda - Z370 X Code



torsdag, 24. maj 2018, 13:25

Re-posted i 1. post hvis ikke du har set det der kommer det igen her: :finger:

24/5-18 13:23 (sorry for the delay) FINISHED PICTURES, LETS REVEL THIS PANDA!

A big thanks for everyone showing an interest in this build, it's been a long journey and it does not stop here, I'm still not done with the closet to put it in or the new desk setup, so will do some little updates as that comes along to.

But the main attraction is done:

It's a really really tight fit to make everything I wanted possible in this case, but I did it!

Bonus beauty shot:

My re-made GPU cooler and active m.2 cooler is both working like a dream

That slim 15mm fan was a really good idea, on top of a AquaComputer Kryo M2

Everything from my extended PSU mount, to my external EPS cables and my tons of fans are blending in pretty neatly IMO.

If I had not made a long build log about it, then you would probably not have a clue about all the work I have gone trough, I have exchanged every screw and pop rivet in the case, painted, put vinyl, drilled and more on all surfaces.

It was already a very rare and unique case to begin with, now even more so.

And now, the killer panda!

The really strong sunlight played monkey tricks on me, it is red and black, not orange, will try and get better pictures indoors another day.

Will finish up with the closet and desk setup in the coming days, stay tuned if interested in that ;)

Min gaming PC: Killer Panda - Z370 X Code



torsdag, 24. maj 2018, 13:37

Hvor er det et godt stykke arbejde!


torsdag, 24. maj 2018, 13:53

Hvor er det et godt stykke arbejde!

Takker :)

Jeg er lidt stolt over at mine total bananas tegninger i Sketchup faktisk er virkelighed nu

Der var engang det bare var piperensere, nu er det den ægte vare


Min gaming PC: Killer Panda - Z370 X Code



torsdag, 24. maj 2018, 14:36


Det ser sgu fedt ud!

The Hoff - Mansens 80er Retro PC
| NZXT H700i| Gigabyte Aorus X370 Gaming 5 | Ryzen 1700 @4.0GHZ | 4x8GB Trident RGB 3200Mhz @2933 Mhz RGB | MSI 1080 Armor OC 8GB | Be Quiet Dark Power Pro 11 650W | 1x256GB, 1x512GB SSD | 6TB NAS Harddisk | Vandkøling fra EK, Hardwarelabs og Enermax |


torsdag, 24. maj 2018, 14:43


Det ser sgu fedt ud!

Toppen af kransekagen bliver når jeg får det ind i skabet, med spejle lys og aktiv køling, men det bliver ikke idag... Alting tager utroligt meget længere tid end man regner med når det skal gøres ordentligt.

Min gaming PC: Killer Panda - Z370 X Code



fredag, 25. maj 2018, 09:08

Har lige smidt den på PCPartsPicker, når man sådan regner det sammen så kom den alligevel til at koste en del.....
Oven i det skal der så tænkes på at priserne der er meget billigere end i DK :ph34r:


Var egentlig ved at downloade spil så jeg kan få overclocket grafikkortet med real world loads, men det tog seriøst lang tid og kunne ikke helt forstå det, indtil det gik op for mig min spil harddisk havde 35% fragmentering!

Så om 16 timer er OO Defrag færdig med at rette op på det lille problem og alting skulle igen køre efter planen :cheers:

Min gaming PC: Killer Panda - Z370 X Code



lørdag, 26. maj 2018, 23:47

Delays, delays, delays....

I have been working all day to finish up the room setup and finally sat down to use it, was just about to take pictures until I discovered that my displayport cable refuses to display anything else but 1024x768@60 Hz for my new fancy monitor....

It's really odd, as the same cable without hiccups can display 1920x1080@144Hz on my old monitor placed right next to this newer one.

Well I dont see any way around it but have ordered the best 8K capable DisplayPort 1.4 cable I could easily find, plus a high end shielded power cable as I suspect that's maybe the problem (they run right next to each other).
Remember, the PC is placed in the other end of the room, so the DP cable is actually 10 meters long, this new one will be routed a different route and only have to be 5 meter then, all those changes can only mean it's going to work this time around. Else I will have to re-think everything... hope not....

But I tell you, the idea about mirrors in the closet works like a charm, it's really easy plugging this in or out from behind the system and it looks really nice too, will show you when everything is up and running.

FORRESTEN, et spørgsmål - skal jeg lave en ny tråd med det endelige færdige resultat eller skal jeg blive ved med at poste i den her?
Det er ved at blive lidt rodet herinde...

Min gaming PC: Killer Panda - Z370 X Code



lørdag, 26. maj 2018, 23:53

Bare post i denne. Jeg tror det vil blive mere forvirrende, hvis du laver en ny tråd.



søndag, 27. maj 2018, 11:52

Det ser lækkert ud :-D er der ikke stadig en case like d sektion? Du kunne Evt smide fotos ind der også så den ikke går i glemme bogen :-)

Fx 8320 | Asus R9 280x | ASUS M5A97 EVO 2.0 | 8 gb G.Skill ARES 1866 MHz cl9 | 120 gb samsung 840 evo ssd
Canon 700d - Røde videomic go


onsdag, 30. maj 2018, 13:57

Vauw, den er blevet fin :)

Men er nødt til at høre, de kabler der stikker ud bagpå, kan de på ingen måde være inden i kabinettet?
- Mathias


onsdag, 30. maj 2018, 14:22

Vauw, den er blevet fin :)

Men er nødt til at høre, de kabler der stikker ud bagpå, kan de på ingen måde være inden i kabinettet?
- Mathias

Der er absolut ingen plads i det her kabinet, ingen, jeg har maxet det totalt ud på alle leder og kanter.
Det gav bedst mening at lade EPS kablet køre udenpå bagom PSU, for det første fordi jeg aldrig kommer til at kigge deromme men også fordi det så ikke sidder i vejen for hverken looket indeni samt airflow over komponenterne.

Du kan se, fordi strømforsyningen er nedenunder bundkortet så er der praktisk talt kun 3 steder i kabinettet det vil kunne lade sig gøre og få kablet op, men så skal det løbe enten over eller under en masse ting, for at nå op i hjørnet hvor det hører hjemme.

Cirklerne er de 3 steder jeg snakker om, stregerne er der kablet ville kunne komme til at løbe

Jeg har brugt siden slutningen af november på at gennemtænke, tegne og bygge den her maskine, jeg tror jeg har fundet den bedste opskrift for at det hele kunne lade sig gøre, men sig da endelig til hvis du ser et eller andet jeg har overset - kan jo altid lave en version 2.0 ;)

Min gaming PC: Killer Panda - Z370 X Code



onsdag, 30. maj 2018, 14:49

Let me give you a small update, i'm almost completely done now!

I now have the right cable for full resolution @165hz, 10 meter very expensive DP cable.

Also upgraded my power cable to one as thick as a watering hose, silver plated cobber wires and many layers of shielding, so it should not get affected by the many other wires in the closet plus not affect the rest of the wiring, as power cables usually make the most dirty signal interference with other types of cables.

Fresh air tunnels for the closet is done and doing a really nice job of pushing the warm air the machine generates out and into the atmosphere outside.
I don't want it to suck air in, as that might pose problems when the weather gets colder, but this way around I think i'm safe.

I have tweaked my Windows 10 Pro for maximum performance, and defragmented the games drives (which took forever for a 1TB drive and a 500GB drive), so as of now I am overclocking the GPU.

About the GPU, the cooling does a really really good job with those 2x ML120 fans I put on it, even with the door closed on the closet.
But the OC itself on the GPU, oh boy what a pain, I have really not been lucky with that GPU and it keeps crashing on me.

I have now dialed it completely back and taking baby steps. Just takes forever....

Next update will come when everything is completed and I can actually start using it.

Min gaming PC: Killer Panda - Z370 X Code



torsdag, 31. maj 2018, 23:39

Re-post fra 1. post, så er jeg sikker på I har set det ;)

Desktop update!

This is the front logo seen from indoor light, more like how it looks in real life.
The black aluminum and black vinyl is almost the same tone, so it's only in very specific angles and light conditions that the panda is visible, it's a shy animal.

The closet setup at the spot it was intended to be right from the start.
You can also kind of see the 3x ML140 Pro white light fans there suck air up to the upper compartment, where the other 2x ML140 fans are placed on the inside of the air ducts - with the help of the 2x ML120 inside the ducts to draw the hot air out.
Works better than I could have hoped for actually, at idle the CPU is staying around 40C with a very warm room temp of 27C because of summer.

Tried to take pictures so you can see the helping mirrors, they are mostly for a purpose other than *bling*, but actually they are more useful when the system it not finally installed and the system can be pushed around a little, as I can way better look behind it and inside it, to see if everything is installed the way I intended it.
Remember, it is a closet after all, there is really limited space and I have to stand on something to reach there, so to get all the help I can i.e. to plug in a cable behind, that is a huge bonus.

Speaking of mirrors, I did the same behind my big a$$ monitor.

Here it's slightly easier to show you what the purpose is.
I can see the inputs!

Looks like this from the front, the "bubble" at the end of the table is my brand new Hue Go lamp that I just picked up, am charging it now to play around with tomorrow.

Same setup looks something like this at brighter light.
Sorry for the colors, my camera and indoor light is not the best combo so tried to compensate in post process and ended up at this.

From another angle

If you wonder why I have 2 keyboards, then the wireless Logitech one is connected to 2 machines below the table, where I'm also hiding my music DAC I use for well yea, music, and right now my surround headset is plugged into one of the machines, my "Mini3" i3 based tiny magnetized PC that can carry it's own weight under one of the desk shelves.
The other one is an even lower powered Linux machine only used to browse the web on, if I don't need any power for anything extra, build both of them out of scrap parts I had laying around from other builds that are worth too little to sell but are too good to throw away.

I'm trying to keep it pretty clean with no visible cables under the desk, mainly because my son loves to stay under there when I play games, so he can watch a movie or sleep.

Stay tuned if interested in a last update about the numbers of this PC, all the specs and benchmarks. Cheers m8 :cheers:

Min gaming PC: Killer Panda - Z370 X Code



søndag, 10. juni 2018, 21:55

re-post fra 1. post - jeg har endnu ikke rigtigt lagt nogen benchmarks eller andre former for lækre tal op, for jeg fandt ret hurtigt ud af det ikke gav mening uden at jeg havde noget at sammenligne med, som var lavet på samme grundlag.
Så jeg er faktisk gået igang med at bygge et system, så vi kan sammenligne :ph34r:

Men her er det store spørgsmål så - vil I have en tråd om det nye system allerede, der er ikke så meget at se, men jeg kan tease det ;)
eller skal vi hellere vente til der reelt er noget at se?

Det bliver om noget nok endnu mere unikt end det her, så jeg kan sammenligne to ret unikke systemer så det allerede set fra den vinkel kan sammenlignes, ikke kun benching metoden som er ens.


Min gaming PC: Killer Panda - Z370 X Code



torsdag, 21. juni 2018, 01:55

Re-post fra #1

Jeg er nu stille og roligt igang med at opbygge det system der skal måles op imod Killer Panda for at se hvor vild min gaming PC fra 2018 egentlig er.

Følg med i den nye tråd her.

Min gaming PC: Killer Panda - Z370 X Code



onsdag, 15. august 2018, 22:03

Killer Panda er på krigs stien igen!

Blev idag featured på Battlerigs på Instagram - den her maskine er der godtnok mange der rigtig godt kan lide.

Er så småt gået igang med at bygge modstanderen samt har lige pt et Ryzen build på test bænken som jeg bygger for en ven, skal nok blive en god sammenligning i sidste ende.

Den her historie er langt fra slut endnu ;)

Min gaming PC: Killer Panda - Z370 X Code



søndag, 2. september 2018, 01:40

Se det her er hvad Killer Panda er til for!
Strange Brigade 1080p gaming på Ultra kvalitet med gennemsnitteligt 100FPS :D


Den her maskine er en kæmpe success!

Jeg er blevet opereret for 14 dage siden og måtte lige sætte alle projekter på hold, midt i det udkom Strange Brigade så det var nu ikke så skidt en da, da jeg igen kunne sidde nogenlunde op i længere tid af gangen blev der tid til at spille lidt.


Min gaming PC: Killer Panda - Z370 X Code


Nyeste Videoer og Trailers

Partner sider
Indsend nyhed
Har du fundet en fed nyhed så indsend den så alle andre på Tweak.dk kan få glæde af den.