28

fredag, 11. maj 2012, 00:54


I had just finished mounting the fans when UPS showed up with yet another package:





Inside it my Raidon HDD box and my new fan for it + a surprise (a free microfone, I do have a camera but never bothered getting a mic for it - how did they knew that?!):





The noisy standart fan had to come off:





Some stripping:





Off with the tacho wire:





Ready to solder:





Problem is though, found out I am out of solder and I lost my heatgun..... Went for the next best thing: Glue and tape!
Just temporary until I get solder, find my heat gun and receive the package from US were I ordered some tiny cable sleeve and heat shrink.


A few rubber discs to prevent vibration (the original fan was just mounted straight on the frame):





Done deal (for now), the fan is mounted so it sucks air out of the box into the chassis, just like the original fan did:





Mounted both drives in the box, an extremely tight fit, so tight it make it bulge a little:





The frame is black plastic, but the doors are painted aluminum that match the painted steel chassis very nicely:





Another detail I really like about this box is that there are no buttons to accidentally hit and eject the discs - you need a special little tool that is in the box to get your HDDs back out (so don't loose it).


Plugged them in via a small USB to Sata adapter I normally use for data recovery or general drive testing:





Yep it is alive, fan working, LED lighting and discs spinning:





A strange little thing that happened when I plugged it in is that my Mac can only see the 3TB Hitachi as 800GB?
Why is that - Mac don't support 3TB or is it the controller in my USB adapter that have a limit?





Todays finished work with fans mounted, PSU mounted, MB mounted and fans plugged into MB (I think I did a pretty good job in cable management:





I hope I get a visit from DPD tomorrow with my Lian Li drive cages and in the beginning of next week I should receive my first package from Performance PC's.
As soon the drive cages have been mounted I will order SATA cables to get the right length.
Also, I want to prepare to max it out with the total 8 drives, so I need yet another package from US with these in.
More updates will follow as the work continues when more parts arrive.

Stay tuned :drink:

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

Dette indlæg er blevet redigeret 1 gange, senest redigeret af "AT0MAC" (11.05.2012, 01:07)


29

søndag, 13. maj 2012, 19:04


I have received my Lian Li drive cages and on Monday I will start to figure out how to make them fit in the case.


I have been looking around for a way to neatly bring power to my six drives in the Lian Li cages (there is only one drive for now but it never hurt to think ahead).
I asked the guys over at Perfomance-PCs if they could help - and sure thing - they have sponsored me to custom make me a pair of molex -> 3x sata power plugs!
Red wires to match with SATA data cables, black sleeve and black heatshrink... Can't wait to receive their package and thank them SO SO much for the sponsoring - go check out their site, if you are into modifying and cleaning up your PC act they are the place to go!


The cables they have sponsored me are similar to these:





Another update is I have started to make a "pixel perfect" model of the whole build - so far I have made like 80% of the Norco case up to scale with mm precision.
Because of that I figured out there is actually no place I can put all my case badges - I know the server is supposed to hide under my sofa, but whenever I take it out I like to show off directly on the case what awesome equipment it is made from - so I ordered a piece of 25x600mm real woven and lacquered carbon fiber plate! (that was a little pricey but it is going to look epic!) - not any fake sticker or plastic plate printed to look like carbon, this is the real deal!


I am assuming I will cut it to fit and mount it on the front like this (but lets see when I receive it):





The square in the middle is a Performance-PCs case badge :)


I am now officially modder! I draw in 3D, modify and even gets sponsored! :D

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

30

søndag, 13. maj 2012, 20:26


Just updated post #1, a little of who I am, what I have done before and most recent update pictures :)

Stay tuned :rules:

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

31

mandag, 14. maj 2012, 22:45


I learned a small lesson today:

The guys and girls in crime show CSI are right about Glue fumes making fingerprints visible!

That is what have happened to my NoiseBlocker fans because I glued in the PWM wires, they were a little loose from the factory and would not stick in their plastic bracket.
It now looks like this:



The white parts is finger smudges...


Tried to clean it off with some alcohol, got better but not pristine:



:(


In other news, received my first package from Performance-PCs today:




Inside it was heatshrink, sleeve and rubber edging for my steel cut outs:










Just realized I had not put up pictures of my new drive cages, so here you go:
















Tomorrow I hope to have time to sleeve, am still waiting to receive my piece of Carbon fiber and my second package from Performance-PCs. These last few weeks I feel like I am running an import company, SO many packages and deliveries to take care of!


By the way, I need your help: This build need a cool name, what do you suggest I call it?

Primary components are Norco case, NoiseBlocker fans, Hitachi drives, Atom processor, mITX SuperMicro motherboard and a small piece of carbon to finish it off. What names can you come up with???

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

32

fredag, 25. maj 2012, 19:46


Hi guys - I'm back!


Sorry for the loss of updates, but I have had a lot of work at my primary job and I have had a lot of trouble with the last few pieces of this build.


First of all I have not yet received my carbon, should arrive one of these days.


Second, my package from Performance-PCs containing power cables for the drives got a little lost. First it arrived, then I went to pick it up, it was no longer there - and today I finally found out it was because customs had picked it up to get it tax evaluated. So today I received it and the cables looks absolute AWESOME!!




Updates in pictures:




Been sleeving cables for the buttons/LEDs in the front of my case:





Half way there:










Finished:





And the other end:





In total:





Here is the package from US based Performance-PCs who supported me by sponsoring a pair of their really really nice looking power cables:





And here is the cables them selves!!!





Click the logo to go directly to their site for inspiration or to buy the best in computer parts for builders/modders:


DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

33

mandag, 28. maj 2012, 22:35


ser ud til at blive et super lækkert build det der =P

Hvorfra fik du dine SD kort? har selv overvejet og skifte til den slags kort som du bruger, men kan ikke lige finde en forhandler :S
Måske mig som bare har overset det, men bør du ikke smide lidt støvfiltre foran dine 80mm blæserene nu hvor din Server skal ligge under sofaen?

If you make it idiotproof then some will just make a better idiot.. =P

Asus Maximus III Gene
I7 - 860@4Ghz Corsair H70
Gainward GTX470
Corsair Dominator GT PC17066 4 x 2GB
Creative SB X-Fi XtremeMusic
OCZ Vertes 3 + Intel x-25 m80 2.Gen Triple boot: Lion, W7,Ubuntu
Dell U2711 + vertical Samsung SyncMaster 226BW

34

mandag, 11. juni 2012, 01:12


ser ud til at blive et super lækkert build det der =P

Hvorfra fik du dine SD kort? har selv overvejet og skifte til den slags kort som du bruger, men kan ikke lige finde en forhandler :S
Måske mig som bare har overset det, men bør du ikke smide lidt støvfiltre foran dine 80mm blæserene nu hvor din Server skal ligge under sofaen?


Der er et link et sted i traaden til hvor SD kortene er koebt, men det er ikke saa relevant for jeg koebte de to sidste de havde :p
Der bliver ikke rigtigt lavet SLC kort mere, kun som CF.

Mht til stoevfilter, jeg har overvejet det men vil gerne have nogen som saa daekker hele front og bagside, men kan ikke finde noget stof/filter der er velegnet til formaalet (plus, vores gulv er meget rent saa tror faktisk ikke det bliver noget problem)


-------------------
UPDATE:
-------------------

Im sorry I been quiet for so long yet again, but these days I have a lot of work to do in my primary job so not so much spare time to have fun in :(

Anyway...

I have many many pictures I will post whenever I get time, just to mention a few things I have made so far since last time:


  • Been drawing super precise 3D drawings of the build (drawings are not completed yet though as it takes immense amounts of time)
  • Cutting the Lian Li case drives a little smaller so they will fit better
    Ordered a Scytche Quiet Drive 2.5 for the cache disc as it will be the only drive running most of the time I would love to make it the most noiseless (and also make it able to fit in the other 3.5" drawers)
  • Changed my mind to that I will not use the Raidon frontmounted 2.5/3.5 combo drive box as it obstructs my other drive cages (the box is a few mm too wide) and also because in my testing so far the 40mm fan is super annoying (even after I changed it to a more noiseless model)
  • Just ordered a XFX Radeon 5450 low profile graphics card with DVI/VGA/HDMI because I am considering running a dual boot system with either Windows 8 Server or Ubuntu 12 - to use as a low-end HTPC
  • Thinking about buying a Logitech Dinovo Mini for the HTPC usage
  • And lastly, the carbon fiber piece I had ordered in the UK never arrived because it was too long to send as a normal package. Didn't want to overspend on it so have asked for a refund...




Thats all for now, stay tuned till next time I swing by and post pictures and niceness :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

35

onsdag, 13. juni 2012, 23:58


Let me share a few of my newest sketches, so you can see I am not totally abandoning this project :)
It is still in progress, just a little slow due to other work wich pays more than spare time projects tend to do :p


----------------


This is one of the reasons to why I can not use the Raidon box, the space will be a few mm too tight (the grey in front of the fan is the side of a drive cage obstructing the way the front module would be placed normally):



A birds view of the whole thing, notice the black PCB left in the Motherboard, thats the graphics card (only drawn the gfx in estimated size as no one seems to have measured a 5450 card before):





"Glass box" view (were you clearly see the drive cages and back plate both in mm precise drawings):





Same view, different angle:





Will start moving the whole build to my workplace, as I these days spend more time there than home I could easily progress faster than I can here.
Also my wife would love if I did not use the whole living room as my playground :p




Stay tuned! :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

36

mandag, 18. juni 2012, 22:02


I was recently told I am really good at over complicating things....
So, to keep it short for once:


I received my graphics card but have today chosen to send it back for a refund - reason? There are much better media streamers out there than what I can build my self, it's not worth the effort. Let's keep this NAS simple and efficient! A real pro-nas is no nonsens, so thats the way this will be too.






Another package I received is the disc silencer from Scythe:





A pretty serious little box:





Pure tech porn:








Exposed:





Measuring the bare drive:





Measuring the drive in the box:





Pretty big difference!
It is absolutely silent, or at least it's same as the noise level for the rest of the room - a typical living room noise level.


By the way, since I started modding this project I have found small details everywhere that I can do better.
For once, in the silencer box the thick rubber pads push so much on the drive it actually refuses to start...
And if I remove the pad there are so much air in the box that I can hear something vibrate...
Solution? STP damping mat! Made for silencing doors in car-fi setups, heavy self adhesive pads that can be cut in any shape.





Works like a charm!
Closed up and silent!







Stay tuned for more updates in the near future :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

37

tirsdag, 19. juni 2012, 22:07


Over night I tested the 2.5" drive in it's box to see if it was still ok, simply because when I tried to close the drive the first time with the original rubber inlay it sounded like a "head crash" - but all sectors seems to be in perfect working order :)




Today I have been trying to figure out were to place the cache drive and the parity drive, I would like them not to be among the data drives so they are easier to find and to maximise space.

Tomorrow I will hopefully do some real world testing but for now I let the pictures talk:







What you can see in the back corner is the two drives placed in one of the original hardddrive cages from the Norco chassis, I can hopefully fit it next to the PCI slot and place my Lian Li fan assembly above it for extra cooling.






Stay tuned for more updates in the near future :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

38

mandag, 25. juni 2012, 23:30


A few days ago I had the time to mount the drive cages, and here is the proof:





Used the original drive bay holes in one of the steel plates:





The cardboard is the same size as the motherboard:





An extremely nice fit:





Distanced the drive holders with a few mm in between, for minimal vibration:





Time for some real modding:





Original drive holders in a new position, keeping parity and cache disc in place:



DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

39

mandag, 25. juni 2012, 23:37


I have decided to buy a IBM M1015 controller to run some of the drives from, since 6 SATA ports on the MB was eventually not enough...


Will not receive the card until 7-20 days from now, so all I can do for now is drawing it:








It fits just perfectly!





Stay tuned for more updates in near future :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

40

tirsdag, 26. juni 2012, 21:30


And now the news:


Today I had a few minutes to pull out the "Dremel" and cut away little more of the original 5.25 cage because I had an epiphany... The newly sleeved front PCB were the USB, on, restart buttons and LEDs are placed, it used to be mounted in the bottom of the drive cage!


But with the drive cage totally rearranged that is no longer possible... So a new solution had to be cooked up and I've come up with a small mounting plate cut out of the original bottom, will be "welded" into the front with chemical metal.


So here we go modding away:







Off to a pretty good start:





Done deal:








The front lip it will be "welded" into the front with:





In other news, the things I ordered yesterday from Germany, like the IBM M1015 controller, have already shipped - so if everything go according to what I guess then I have it here before the end of the week :)


Tomorrow I will see if I can get time to measure cable lengths so I can order the last little detail - SATA(n) and SFF8087 cables!

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

41

mandag, 2. juli 2012, 08:41


Still building...


Or more precise, still waiting till I can finish the build!


The guys in Germany I ordered my IBM controller from seem to have been a little fast sending out an email saying it was shipped, because today I received a tracking number that shows the package have not been touched until today... So sometime later this week I should get it.


That's not all, I need cables! I have not measured in real because nothing is really assembled yet, but I measured on my drawing and am pretty sure I got the right length.
I just ordered 6x 12" latching SATA III 90' cables and 1x 19" SFF8087 to 4x SATA III, both in the brand Startech ordered over Amazon in the UK




The last piece I need when those things arrive is my unRAID license code

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

42

tirsdag, 3. juli 2012, 21:14


Lækkert og se dit build skrider fremad mester =)

Personligt venter min nye Unraid server på at V5 kommer i final release inden den bliver samlet =)

If you make it idiotproof then some will just make a better idiot.. =P

Asus Maximus III Gene
I7 - 860@4Ghz Corsair H70
Gainward GTX470
Corsair Dominator GT PC17066 4 x 2GB
Creative SB X-Fi XtremeMusic
OCZ Vertes 3 + Intel x-25 m80 2.Gen Triple boot: Lion, W7,Ubuntu
Dell U2711 + vertical Samsung SyncMaster 226BW

43

tirsdag, 3. juli 2012, 21:18


Personligt venter min nye Unraid server på at V5 kommer i final release inden den bliver samlet =)


Samme her, regner ikke med at starte og bruge den foer v5 er officielt ude af RC/beta.


Update:
Regner med at modtage min IBM controller imorgen, fik ihvertfald seddel fra UPS idag om at de havde forsoegt. Derefter er det kun kabler jeg venter paa, skulle gerne ankomme inden der er gaaet en uge.

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

44

mandag, 9. juli 2012, 21:20


I have now decided that as soon as the whole thing is assembled and I can get my GUID, then I will buy a unRAID Pro key... Rest of the system is already pretty much Pro so why the hell not :p


In other news:


German retailer ALB computer made a mayor error and forgot to send my IBM ServeRAID card!
They only send a bunch of smaller thing's I needed for other reasons :(
I am currently trying to get them to understand that I am not cheating them and the card was for real not in the package, but they are German and Germans apparently are not good at taking critic... I hope it will end well...




You see here, no IBM PCI-express card:





So now when I am again just waiting I better do some real work... Today I smoothed out the little bracket I cut recently.


Before:





After:





Molded my chemical metal, that had become a little overdue so it dried up way much quicker than normally (normally it takes around 10 minutes so you can shape it) wich ment it looks not so nice... But who cares, it will not be easily visible.








Looks like I measured correct, because with just a little squeeze the front PCB board fit nicely in place. Even tested the USB and is still easily accesible.





Later in the day yet another brown borring package from the UK arrived:





Inside it was my 50cm SAS cable and my 8 SATA cables:





But why 8? I just like to have a few spares...
Because as they say on the package, good quality is hard-to-find









I hope I can get a few hours to assemble more tomorrow... I want to hopefully finish this build before this month have passed (but with my luck it might not be possible...)




Stay tuned :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

45

torsdag, 19. juli 2012, 23:28


A bunch of pics!!!




I installed rubber grommets on all screws in the cabinet














Ready to assemble:



DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

46

torsdag, 19. juli 2012, 23:29


Installed the fan in my Lian Li mount:





Sucking in, blowing down:





Installed:








Feet:





Antivibration thick rubber:



DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

47

torsdag, 19. juli 2012, 23:29


My IBM RAID card:





Installed:





Prepared USB for my boot drive:





First HDD installed, 2TB Hitachi:





Mounted with rubber:





Secured cables:





Put rubber list on all sharp edges:






DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

48

torsdag, 19. juli 2012, 23:30


Securing cables:





Installing boot drive SD card reader:





SATA cables:








Naming them:





Ready to install:





Plugged in:



DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

49

torsdag, 19. juli 2012, 23:31








Assembled front view:





Only missing the front and the top:





Front installed (have to do something about the open 5.25" hole)





Everything assembled:





Turned on for the very first time:




Now I reached the part were it's all about software, I am not a software guy so this is the absolute tricky part for me :(


Stay tuned to see the final pics whenever I finish it up :)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::

50

lørdag, 8. september 2012, 20:57


1)
It seems as the motherboard is faulty somehow, no matter what I do it refuses to boot from USB (but I will though have to test with a boot cd and a drive one of the coming days).

2)
My wife got very sick and had to give birth to our daughter 5 weeks before time, so ever since the previous post I have been taking care of my two girls. Both are fine by now.

3)
Because of 2) we have moved the living room furniture around and it's no longer ideal to have a server below the couch, so I need to find another case to contain it in.

4)
Because of 2) I now have many pictures and video I would never be able to recover if anything happened to my storage media, so backup is utterly important now! I need to backup to the cloud for off site solution and peace of mind. (unRAID can not do that, so I am going the Linux route now).

5)
My primary Mac Mini have now moved from a desk to the sofa area and are therefor now a HTPC solution, therefor I need a server capable of running Plex (transcoding not important).

6)
Want something easy, plug and play without major surgery - a Hackintosh Lion Server would have been top nice, but no mITX seems to be supported. My eyes caught the Lian Li PC-Q11A case and that's what Im going for with my current 5 TB drives (will add a few 2.5" drives in the near future for somewhere between 1-2TB more storage).


To be honest I had first seen the PC-Q07 because it is absolute cheap!
But I would have to do some very strange things to it:


Cut out and make rom for the MB in the bottom, plus cut some mesh sheet to cover up all the extra holes in the back.


Barely fit one of my Lian Li drive cages inside for up to 3x3.5" drives but no PSU (would have to be externally or pico PSU).


The box to the side is the normal ATX PSU I am using, tiny tiny case!


...but after drawing it I realized it's not worth the trouble.


THIS is much more doable:






(trick photos, not actual pictures)


Cherry on top - I can even fit my DVD-burner in the case! Have an old Lacie D2 laying around not really using it because it's not primary connected and too much trouble to do so whenever I need a DVD/CD...

:clap:

Stay tuned, this time it will not take forever before things happen (I hope)

DualCore Pentium :: G2030 :: 4x2GB DDR2133 :: 2x Intel520 240GB SSD RAID0 :: Asus GTX 660 TOP ::
:: X400 Passive SeaSonic :: NoFan CS-70 :: Dell 2209WA :: Mionix Naos 5000 :: Apple Pro keyboard ::


ASUS ROG Maximus VII Hero

Endnu et bundkort fra ASUS Republic of Gamers serien har ramt Tweak.dk redaktionen, og det er med stor fornøje
Læs Mere

Pure Pop Mini FM/DAB radio

Pure, som laver lydudstyr af høj kvalitet i en klasse for sig selv, har denne gang tilsendt os en FM/DAB radio
Læs Mere

ADATA XPG Z1 2400 MHz DDR4 16GB kit

Endnu et 16 GB DDR4 kit har fundet vejen til Tweak.dks testbænk, og i denne omgang er der tale om ADATAs XPG Z
Læs Mere

TP-LINK 7-Port USB3.0 hub

TP-LINK, som ellers normalt laver ting til kommunikation, kommer denne gang lidt ud over deres eget sortiment
Læs Mere

Rapoo E9090P Wireless Illuminated Keyboard

Denne gang har Rapoo sendt os et af deres trådløse tastaturer. Dette tastatur er helt sit eget, da det har bel
Læs Mere

ASRock X99E-ITX/ac

Står du og overvejer at bygge et mITX system, men er du på samme tid interesseret i et lille vilddyr med masse
Læs Mere

ASUS Sabertooth X99

Sabertooth serien kender de fleste af os som toppen af poppen i ASUS TUF serie af bundkort, og de har i denne
Læs Mere

ASUS Strix Tactic Pro Gaming Keyboard

Det er igen blevet tid til at anmelde et produkt fra ASUS' Strix serien, og denne gang er det et tastatur, der
Læs Mere

Problemer med Samsungs eget cover?

Der indløber på nuværende tidspunkt flere klager fra Galaxy S6 Edge ejere om, at det originale Samsung ClearVi
Læs Mere

Alle ASUS 100-series bundkort afsløret

Et asiatisk website menes at være i besiddelse af en komplet liste over alle de ASUS bundkort, der kommer i lø
Læs Mere

Samsung bekræfter Iron Man edition af S6 Edge

I sidste uge kunne vi fortælle jer om, at Samsung havde teaset med en Iron Man version af Galaxy S6 Edge på Tw
Læs Mere

Er dette fremtiden for kortbetalinger?

Tænker du nogensinde over, hvad du gør, når du sætter dit betalingskort i terminalen og trykker din PIN-kode?
Læs Mere

BIOSTAR fremviser det første LGA1151 bundkort

Med lanceringen af den kommende Skylake processor fra Intel senere i år får vi også nye bundkort dertil. De ko
Læs Mere

Carmageddon: Reincarnation lanceret

Spilproducenten Stainless Games, der har udviklet efterfølgeren til Carmageddon-serien, har netop lanceret spi
Læs Mere

GIVEAWAY! Vind en tur i biffen med Tweak.dk!

Vi er super glade for jeres engagement på både Tweak.dk og begge vores Facebook grupper, hvilket naturligvis o
Læs Mere

Spotify laver ny sportsfunktion

Spotify, der er kendt som musikstreaming giganten, som mange elsker at bruge, har netop lanceret en ny funktio
Læs Mere
Nyeste Videoer og Trailers

Indsend nyhed
Har du fundet en fed nyhed så indsend den så alle andre på Tweak.dk kan få glæde af den.